Made in USA
The Embedded Solutions Experts
cPCIRepeat32
cPCI to PMC compatible adapter/carrier with PCI bus expansion
cPCIRepeat32 Description
- PMC Module position with 32 bit, 33/66
- ET operating temperature range -40ºC to 85ºC
- Storage Temperature range -40ºC to 100ºC
- Relative humidity 5-95% non-condensing.
- Conformal Coating is available for condensing environments
- Fan option with Zero Slot Fans™
- PMC Bezel IO
- PCI bus expansion
- 1 year warranty standard. Extended warranty available.
- Extended [Industrial] Temperature standard.
- ROHS and Standard processing available
cPCIRepeat32 design´s primary purpose is to provide bus expansion for a passive cPCI backplane. The embedded bridge expands the PCI bus with 4 additional positions including clocking, interrupt routing, bus requests and grants. J2 has special signal definitions to bring the secondary side to the backplane. In addition, cPCIRepeat32 has a built in PMC position. The bridge can operate with 5V or 3.3V PCI signaling. Designed for 32 bit data bus width with 33/ 66 MHz bus operation.
The PMC bezel connector is mounted through the cPCI mounting bracket. cPCIRepeat32 is an extended temperature design. -40C to +85C standard. Conformal Coating is an option. For boards requiring cooling, fans are available.
Voltage monitors check the 5, 3.3, +12, and -12V rails and illuminate LEDs when within specification. The LEDs are visible through the cPCI bezel, and labeled in the silk-screen.
Power is routed from the cPCI backplane to the PMC connectors with mini-planes, each of which is rated for more than the maximum PMC draw [10-12A per plane] for the 3.3V, and 5V. VIO, +12, -12 have similar overbuilt planes with also more than matching the PMC connector capabilities. The 3.3V and 5V planes are LC filtered to provide isolation from conducted noise. This feature will help with noisy backplanes and power supplies.
cPCIRepeat32 has a low internal power dissipation. The dissipation is a function of the frequency and load from the installed PMC. The bridge uses 1W at 66 MHz and less at 33 MHz. The terminations contribute additional dissipation for a total of less than 1.2W at 66 MHz. Please add your PMC requirements to the 1.2W figure for total power utilized in the slot.
If you have custom requirements please call or e-mail us with the details.
The PMC bezel connector is mounted through the cPCI mounting bracket. cPCIRepeat32 is an extended temperature design. -40C to +85C standard. Conformal Coating is an option. For boards requiring cooling, fans are available.
Voltage monitors check the 5, 3.3, +12, and -12V rails and illuminate LEDs when within specification. The LEDs are visible through the cPCI bezel, and labeled in the silk-screen.
Power is routed from the cPCI backplane to the PMC connectors with mini-planes, each of which is rated for more than the maximum PMC draw [10-12A per plane] for the 3.3V, and 5V. VIO, +12, -12 have similar overbuilt planes with also more than matching the PMC connector capabilities. The 3.3V and 5V planes are LC filtered to provide isolation from conducted noise. This feature will help with noisy backplanes and power supplies.
cPCIRepeat32 has a low internal power dissipation. The dissipation is a function of the frequency and load from the installed PMC. The bridge uses 1W at 66 MHz and less at 33 MHz. The terminations contribute additional dissipation for a total of less than 1.2W at 66 MHz. Please add your PMC requirements to the 1.2W figure for total power utilized in the slot.
If you have custom requirements please call or e-mail us with the details.
cPCIRepeat32 Features
Size
6U 4HP cPCI
Positions
1 PMC position provided
Clocks
cPCI bus can operate at 66/50/33/25 MHz. The PMC must be 66 MHz capable for 66 MHz operation to work properly. User switch to allow or disable 66 MHz operation.
Access Width
Standard cPCI byte lanes supported for byte, word, and long-access dependent on installed PMC. 32-bit operation.
Software Interface
PMC register definitions as defined by installed hardware. No software set-up required by cPCIRepeat32.
Interrupts
INTA, B, C, D routed to cPCI connector from PMC. Please see the HW manual for details.
Signal Conditioning
Secondary side PCI signals are routed and terminated IAW the PCI specification.
Power
+5, +3.3, +12, -12V, and VIO suppled to PMC with oversized power planes. Voltages are monitored. When the associated LED is illuminated, the corresponding rail is within tolerance.
VIO
Bridge primary PCI IO Voltage is set by the cPCI backplane. Secondary side VIO is set to 3.3V.
Thermal
cPCIRepeat32 is a low power design with minimal heat dissipation for optimal PMC performance. Less than 1.2W used by bridge and terminations for 66 MHz. 64-bit implementation. 33/32 will be lower. The temperature range is -40ºC to 85ºC. Fans are available for higher thermal load PMCs.
IO Interface
Front bezel IO supported at cPCI bracket
LEDs
+3V, +5V, +12V, -12V and Busmode 1 are displayed on the bezel. Voltage monitor circuits for PMC voltages to check if within proper operating range.
JTAG
JTAG header connected to PMC slot 0 option. JTAG pin definitions are in the silkscreen. Add -JTAG.
cPCIRepeat32 Benefits
Speed
The bridge allows for isolation and for differing clock rates on the cPCI backplane and the PMC.
Price
cPCIRepeat32 represents a cost effective solution to putting extended temperature PMCs into cPCI environments. Make use of existing PMC designs in cPCI applications without paying for the expense of a new design and layout. Quantity discounts are available. Please check the current per item pricing with the storefront lower on this page. Orders can be placed via the on-line ordering system or via phone / email PO order systems.
Ease of Use
cPCIRepeat32 is easy to use. A plug and play interface to the PMC sites and downstream HW.
Availability
We work to keep the cPCIRepeat32 in stock. With our automated assembly system, larger orders can be processed in a short time
Size
cPCIRepeat32 is a 6U 4HP cPCI board which conforms to the cPCI mechanical specifications. Eliminate mechanical interferance issues. cPCIRepeat32 can be used in cPCI bus expansion slots. Please refer to the manual for pin definitions, etc.
PMC Compatibility
cPCIRepeat32 is a PMC compliant device per the IEEE 1386 specification. All Dynamic Engineering PMC modules are compatible with the cPCIRepeat32.
cPCI Compatibility
cPCIRepeat32 is a cPCI compliant for J1 and with the bus expansion pin definitions contained in the manual for J2.
Part Number: cPCIRepeat32
Ordering Options
- cPCIRepeat32 Standard board - extended temperature, cPCIRepeat32 IO through Bezel, PCI expander [J2] installed. Add any of the following build options after the PN as shown below:
- -Fan() Need additional cooling? order cPCIRepeat32-Fan() for a pre-installed 12V 5.2CFM fan(s) to maximize cooling and functionality of your card. The fan has been tested with high wattage PrPMC devices. Valid fan options include: (1 or 1Rz) position 1 only low profile or rear mount.
- -NX cPCIRepeat32 with J2 not installed for a standard cPCI backplane position.
- -ROHS Use ROHS processing. Standard processing is "leaded"
- -CC Option to add Conformal Coating
(2 or 2Rz) position 2 only low profile or rear mount.
(1R) 8 CFM fan position 1 available as R mount only .
(2R) 8 CFM fan position 2 available as R mount only .
cPCIRepeat32 Drivers
Software Support is not required for transparent bridge operation.
cPCIRepeat32 Manuals
Click on the link to Download selected manuals in PDF format.
Download the cPCIRepeat32 Manual Rev A in PDF format.
Download the cPCIRepeat32 Manual Rev A in PDF format.